SILABUS TRAINING CONTROL VALVE : Operation, Maintenance & Troubleshooting

DESKRIPSI TRAINING CONTROL VALVE : Operation, Maintenance & Troubleshooting

(3 days training)

To reduce the effect of these load disturbances, sensors and transmitters collect information about the process variable and its relationship to some desired set point. A controller then processes this information and decides what must be done to get the process variable back to where it should be after a load disturbance occurs. When all the measuring, comparing, and calculating are done, some type of final control element must implement the strategy selected by the controller.

The most common final control element in the process control industries is the control valve. The control valve manipulates a flowing fluid, such as gas, steam, water, or chemical compounds, to compensate for the load disturbance and keep the regulated process variable as close as possible to the desired set point.

Many people who talk about control valves or valves are really referring to a control valve assembly. The control valve assembly typically consists of the valve body, the internal trim parts, an actuator to provide the motive power to operate the valve, and a variety of additional valve accessories, which can include positioners, transducers, supply pressure regulators, manual operators, snubbers, or limit switches.

Whether it is called a valve, control valve or a control valve assembly is not as important as recognizing that the control valve is a critical part of the control loop. It is not accurate to say that the control valve is the most important part of the loop. It is useful to think of a control loop as an instrumentation chain. Like any other chain, the whole chain is only as good as its weakest link. It is important to ensure that the control valve is not the weakest link.
Following are definitions for process control, sliding-stem control valve, rotary-shaft control valve, and other control valve functions and characteristics terminology.

Menimbang cukup kompleknya materi pelatihan Control Valve ini bagi peserta, dibutuhkan training provider yang berpengalaman di bidangnya agar tidak membuat peserta tidak menjadi cepat bosan dan jenuh dalam mendalami bidang teknik ini.

TUJUAN TRAINING CONTROL VALVE : Operation, Maintenance & Troubleshooting

Dengan mengikuti pelatihan Control Valve Peserta dapat berbagi pengetahuan / sharing knowledge mengenai Control Valve dengan peserta dari perusahaan lain yang bergerak di bidang Mechanical

To able know to introduction to control valves
To able know to control valve performance
To able know to valve and actuator types
To able know to control valve accessories
To able know to control valve selection
To able know to special control valves
To able know to installation and maintenance

MATERI TRAINING CONTROL VALVE : Operation, Maintenance & Troubleshooting

Introduction to Control Valves: What Is A Control Valve?, Process Control Terminology, Sliding-Stem Control Valve Terminology, Rotary-Shaft Control Valve Terminology, Control Valve Functions and Characteristics Terminology.
Control Valve Performance: Dead Band, Actuator-Positioner Design, Valve Response Time, Valve Type And Characterization, Valve Sizing.
Valve and Actuator Types: Control Valves, Control Valve End Connections, Valve Body Bonnets, Control Valve Packing, Characterization of Cage-Guided Valve Bodies, Valve Plug Guiding, Restricted-Capacity Control Valve Trim, Actuators.
Control Valve Accessories: Positioners, Other Control Valve Accessories
Control Valve Selection: Valve Body Material, Designations for the High Nickel alloys, Pressure-Temperature Ratings for Standard Class, Face-to-Face Dimensions, Control Valve Seat Leakage Classifications, Control Valve Flow Characteristics, Valve Sizing, Non-Destructive Test Procedures, Cavitation and Flashing
Special Control Valves: High Capacity Control Valves, Low Flow Control Valves, High-Temperature Control Valves, Cryogenic Service Valves, Customized Characteristics and Noise Abatement Trims, Valves Subject to Sulfide Stress Cracking
Installation and Maintenance: Proper Storage and Protection, Proper Installation Techniques, Control Valve Maintenance, Actuator Diaphragm, Stem Packing, Seat Rings, Bench Set.
Studi Kasus / Praktek pemecahan masalah Control Valve

PESERTA TRAINING CONTROL VALVE : Operation, Maintenance & Troubleshooting

Peserta yang dapat mengikuti training Control Valve ini adalah yang ingin mendalami bidang Mechanical

Para praktisi tingkat operator, tingkat penyelia atau perencana bidang perawatan mesin pada industri rekayasa.

METODE TRAINING CONTROL VALVE : Operation, Maintenance & Troubleshooting

Metode Training Control Valve dapat menggunakan fasilitas training zoom atau training online, dan bisa juga training offline atau training tatap muka.

Presentasi
Diskusi
Case Study
Simulasi
Evaluasi

INSTRUCTOR TRAINING CONTROL VALVE : Operation, Maintenance & Troubleshooting

Instruktur yang berkompeten di bidang Mechanical

Victor Malau, Ph.D and Team
(Pakar dalam bidang Mechanical & Maintenance, akademisi dan sekaligus praktisi, yang telah berpengalaman dalam memberikan training & consulting pada organisasi/perusahaan milik pemerintah maupun swasta)

Jadwal Berdiklat Training 2024:

Batch 1 : 6 – 7 Januari 2025 || 15 – 16 Januari 2025 || 22 – 23 Januari 2025
Batch 2 : 3 – 4 Februari 2025 || 12 – 13 Februari 2025 || 27 – 28 Februari 2025
Batch 3 : 5 – 6 Maret 2025 || 10 – 11 Maret 2025 || 19 – 20 Maret 2025
Batch 4 : 14 – 15 April 2025 || 23 – 24 April 2025
Batch 5 : 5 – 6 Mei 2025 || 14 – 15 Mei 2025 || 26 – 27 Mei 2025
Batch 6 : 2 – 3 Juni 2025 || 11 – 12 Juni 2025 || 18 – 19 Juni 2025 || 23 – 24 Juni 2025
Batch 7 : 2 – 3 Juli 2025 || 16 – 17 Juli 2025 || 30 – 31 Juli 2025
Batch 8 : 4 – 5 Agustus 2025 || 13 – 14 Agustus 2025 || 20 – 21 Agustus 2025 || 29 – 30 Agustus 2025
Batch 9 : 3 – 4 September 2025 || 10 – 11 September 2025 || 15 – 16 September 2025 || 24 – 25 September 2025
Batch 10 : 8 – 9 Oktober 2025 || 13 – 14 Oktober 2025 || 22 – 23 Oktober 2025
Batch 11 : 3 – 4 November 2025 || 12 – 13 November 2025 || 19 – 20 November 2025 || 26 – 27 November 2025
Batch 12 : 1 – 2 Desember 2025 || 10 – 11 Desember 2025 || 17 – 18 Desember 2025 || 26 – 27 Desember 2025

Ayo, jangan ragu lagi! Daftarkan segera dengan chat melalui pesan Whatsapp (Fast Respons). Dapatkan pengalaman terbaik dari tim trainer yang berkompeten.
Harga setiap kota akan berbeda serta semakin banyak peserta dalam 1 instransi yang sama, pun akan lebih murah. Untuk informasi lebih lanjut hubungi kami segera.

Investasi dan Lokasi pelatihan:

Yogyakarta
Jakarta
Bandung
Bali
Surabaya

Catatan : Apabila perusahaan membutuhkan paket in house training, anggaran investasi pelatihan dapat menyesuaikan dengan anggaran perusahaan.

Fasilitas :

Module / Handout
Sertifikat
FREE Bag or bagpackers (Tas Training)
Training Kit (Dokumentasi photo, Blocknote, ATK, etc)
2xCoffe Break & 1 Lunch, Dinner
FREE Souvenir Exclusive
Training room full AC and Multimedia

TRAINING CONTROL VALVE : Operation, Maintenance & Troubleshooting