Alamat Kantor

Jalan Raya Tajem, Dukuh Pokoh Baru, Perum Kampung Asri 2 No B2, RT 2 / RW 19,
Kelurahan Wedomartani, Kec. Ngemplak, Kab. Sleman,
Daerah Istimewa Yogyakarta, 55584. Telp : (0274) 4530527





(3 days training)
The Conveyor Design course covers the fundamentals of belt conveyor engineering including: belt width and velocity selection, conveyor power demand, belt sag, drive traction, drive types, brakes and holdbacks, information on conveyor arrangements, vertical curves and transitions, material trajectory calculations etc. plus belt, idler and pulley selection. In many of these topics, outdated conventional design methods are challenged and alternative solutions provided. While some people may feel that they already have an adequate understanding of these topics, the real value of this course comes from the fact that it is packed with practical information that is not available in other texts.
This Conveyor Design course is suitable for engineers employed in the design, operation and maintenance of belt conveyor systems, from graduates with a few years experience, through to engineering and maintenance managers.

Objective :
The objective of the conveyor design course is to give engineers a full understanding of the conveyor design and equipment selection process, together with features of belt conveyors that should be avoided. This knowledge can then be used, not only in the design of new conveyor systems, but also by project engineers involved with new conveyors or existing conveyor upgrades and by those involved with the operation or maintenance of conveyor systems.

1.    Introduction, including brief history of belt conveying
2.    Material properties
3.    Conveyor surcharge angle and burden edge distance selection, including the influence of loading area design and belt velocity on surcharge angles
4.    Idler geometry, including troughing angle and centre roll length considerations
5.    Belt width and velocity selection
6.    Flooded belt considerations including determining the length of flooded belt resulting from overlapping stopping times and the approximate force required to extract material from a blocked chute
7.    Conveyor power demand calculation
8.    How conveyor design packages work, including basic information on rigid body acceleration and deceleration calculations
9.    Differences between rigid body and flexible body dynamic analysis
10.    Belt sag requirements
11.    Drive traction calculations, including what actually happens at a drive pulley
12.    Rubber v ceramic lagging
13.    Outline of drive types
14.    Brakes
15.    Determination of holdback requirements
16.    Transitions
17.    Vertical curves
18.    Conveyor layouts including features to avoid
19.    Uneven wear problems on pulleys
20.    Shuttle conveyors
21.    Travelling trippers, including the design of tripper belt profiles
22.    Take-up systems
23.    Trajectory calculations
24.    Conveyor belting
25.    Skirt systems
26.    Belt safety factor selection, a new method of assessing safety factors
27.    Minimum pulley diameter determination
28.    Pulleys
29.    Conveyor alignment and belt tracking
30.    Idlers
31.    Some general info on the design and construction of the Channar 20 km conveying system

Para karyawan di semua lini bagian Conveyor Design

•    Presentasi
•    Diskusi
•    Case Study
•    Simulasi
•    Evaluasi


Victor Malau, Ph.D and Team
(Pakar dalam bidang Mechanical & Maintenance, akademisi dan sekaligus praktisi, yang telah berpengalaman dalam memberikan training & consulting pada organisasi/perusahaan milik pemerintah maupun swasta)

Jadwal Pelatihan :

  • 2 sd 4 Januari 2018
  • 13 sd 15 Februari 2018
  • 27 sd 29 Maret 2018
  • 17 sd 19 April 2018
  • 7 sd 9 Mei 2018
  • 29 Mei sd 1 Juni 2018
  • 12 sd 14 Juni 2018
  • 17 sd 19 Juli 2018
  • 14 sd 16 Agustus 2018
  • 12 sd 14 September 2018
  • 16 sd 18 Oktober 2018
  • 21 sd 23 November 2018
  • 4 sd 6 Desember 2018
  • 26 sd 28 Desember 2018

Catatan : Jadwal tersebut dapat disesuaikan dengan kebutuhan calon peserta

Invetasi dan Lokasi Pelatihan :

  • Yogyakarta, Hotel Dafam Malioboro, Hotel Cavinton (6.500.000 IDR / participant)
  • Jakarta, Hotel Amaris Tendean (6.500.000 IDR / participant)
  • Bandung, Hotel Golden Flower (6.500.000 IDR / participant)
  • Bali, Hotel Ibis Kuta (7.500.000 IDR / participant)
  • Surabaya, Hotel Amaris, Ibis Style (6.000.000 IDR / participant)
  • Lombok, Hotel Jayakarta (7.500.000 IDR / participant)

Catatan : Apabila perusahaan membutuhkan paket in house training, anggaran investasi pelatihan dapat menyesuaikan dengan anggaran perusahaan.

Fasilitas Training di :

  • FREE Airport pickup service (Gratis Antar jemput Hotel/Bandara/Stasiun/Terminal)
  • FREE Akomodasi Peserta ke tempat pelatihan .
  • Module / Handout
  • FREE Flashdisk
  • Sertifikat
  • FREE Bag or bagpackers (Tas Training)
  • Training Kit (Dokumentasi photo, Blocknote, ATK, etc)
  • 2xCoffe Break & 1 Lunch, Dinner
  • FREE Souvenir Exclusive
  • Training room full AC and Multimedia



Ikuti Kami :

Gallery Foto Training

Be the first to comment

Leave a Reply

Alamat email Anda tidak akan dipublikasikan.